Air Swept Tubular Dryer
The dependable pneumatic drying system that can dry slurries up to 95% moisture in a single pass.
in the Scott Test Lab Facility
Download Now
Download PDF
DISCOVER
Scott Equipment’s Air Swept Tubular Dryer (AST)
The Scott Equipment Air Swept Tubular Dryer (AST) is a pneumatic drying system designed for rugged duty and versatility in many industries. The new, patented drying technology utilizes adjustable paddles and air dams to create optimum air to solids heat transfer. Even slurries, with dry solids content as low as 5%, can be dried efficiently to as high as 99% dry solids in a single pass through the flash dryer.
The agitation provided by Scott’s AST Dryer allows hot air to mix with the wet product entering the dryer inlet, reducing the drying time and breaking up lumps. Materials ranging from filter cakes, thixotropies, and dilatant slurries, powders, and granules can be effectively dried in the AST Drying System.
DISCOVER
Scott Equipment’s Air Swept Tubular Dryer (AST)
The Scott Equipment Air Swept Tubular Dryer (AST) is a pneumatic drying system designed for rugged duty and versatility in many industries. The new, patented drying technology, utilizes adjustable paddles and air dams to create optimum air to solids heat transfer. Even slurries with dry solids content as low as 5% can be dried efficiently to as high as 99% dry solids in a single pass through the flash dryer.
The agitation provided by Scott’s AST Dryer allows hot air to mix with the wet product entering the dryer inlet, reducing the drying time and breaking up lumps. Materials ranging from filter cakes, thixotropes, and dilatant slurries to powders and granules can be effectively dried in the AST Drying System.
Download Now
Download PDF
applications
Air Swept Tubular Dryers are ideal for the following applications:
- minerals
- wood flour
- chicken liver
- steep water
- hatchery waste
- bentonite clay
- tabacco stems
- minerals
- wood flour
- chicken liver
- steep water
- hatchery waste
- bentonite clay
- tabacco stems
- paper sludge
- wallboard waste
- fertilizer
- manure
- kaolin slurry
- food dye
- paper sludge
- wallboard waste
- fertilizer
- manure
- kaolin slurry
- food dye
industries
Air Swept Tubular Dryers are commonly used in:
- mineral
- food
- chemical
- wood flour
DISCOVER
AST Dryer Features
Looking for the comprehensive and dependable drying solution for your next project?
DISCOVER
AST Dryer Operation
The Air Swept Tubular Dryer is a new concept in drying technology. The flow of material through the dryer is controlled, allowing the dryer to process anything from a fine, dry powder to a moist, granular material.
Below, the different operational stages of the AST Dryer are outlined to help you better understand the unique technology behind this innovative flash dryer.
Overview of the Scott AST Dryer
Comprehensive Drying System
Inlet Zone (Zone 1)
The Inlet Zone achieves size reduction (when applicable) and the majority of moisture evaporation. This is accomplished by a highly turbulent agitator area and efficient mixing area utilizing adjustable paddles.
The agitator plates (with a high concentration of fixed blades) work to reduce the product into small pieces and provide a highly turbulent zone for efficient heat transfer. The smaller particle allows for more efficient heat penetration into the material and also allows the moisture to more readily escape to the surface as a vapor. High velocity achieved in this zone, 11,000-12,000 ft/min, further aids in the efficient transfer of heat to the material.
This combination of velocity and agitation, working in concert with a high temperature differential, results in efficient and rapid evaporation. This zone of the dryer is sometimes considered the “flash zone” of the unit.
Further downstream in the first zone are a set of adjustable paddles that allow for back mixing. Product that is still moist and potentially sticky will continue to be agitated and back-mixed via the adjustable paddles until it can be carried into the next zone by the airflow. The back-mix process is continuous with some product being carried over as new product is introduced.
At the division between Zone 1 and Zone 2 is a set of air dams. The purpose of these dams is to classify the product. Material that is dry enough to be free flowing and easily conveyed by the air stream can pass on to the next zone.
Retention Zone (Zone 2)
The Retention Zone achieves product retention, mixing, and drying. This zone is comprised of a series of mixing paddles, adjustable from conveyance to retention. The air velocities in this zone are considerably lower than in the inlet zone. The lower air velocity in combination with the adjustable paddles, allows the product to be retained for the necessary time to complete the drying process.
At the end of Zone 2, there is another set of air dams, which aid in product retention and provide a further means of classification.
Discharge Zone (Zone 3)
The Discharge Zone achieves additional retention, air, and product discharge. This zone is similar to the retention zone; however, this zone contains the air and product discharge and the mixing paddles are typically oriented to achieve discharge.
Feeding System
Provides Constant, Consistent Flow of Product
The purpose of the Feeding System is to accurately control the flow of product into the dryer. A constant and controlled feed to the dryer is important since a continuous system operates best at stable conditions. During steady-state operations, the feed rate is held constant as other parameters are monitored and controlled.
The Feeding System will be the Scott Cake Feeder, Scott Mixer Feeder or a pump (positive displacement or centrifugal), depending on the viscosity of the product to be processed. The feeder is equipped with a variable frequency drive to allow for a ramp up of product flow rate during dryer equipment startup.
AST Dryer
The function of the AST Dryer is to effectively expose the product to the heated process air stream and retain the product until it has reached the specified moisture content. The AST Dryer has three distinct zones with differing operational functions.
Gas-Fired Burner
Directly or Indirectly Fired Provides Efficient Heat Source
The function of the gas-fired burner is to be the source of heat energy into the AST Dryer. The burner heats the process air to an elevated temperature (400°-1200° F) and is responsible for controlling the energy balance of the system. The energy control is achieved by monitoring the process control thermocouple located at the discharge of the dryer. The drying system utilizes a PID loop (via the PLC) to maintain a set point by controlling the firing rate of the burner.
The burner is typically a direct-fired gas burner complete with flame supervision system, fuel train, etc. Other fuel options include propane vapor, fuel oil or an indirectly heated system.
Product Collector and Exhaust Fan
Separates product from the air stream, drawing air through the system.
Situated between the AST Dryer and the exhaust fan is the product collector, which separates the dried solids from the air stream. The industry standard is a baghouse.
The last component in the system is typically a centrifugal fan. The exhaust fan is located on the clean side of the collector and provides the process air required to do the work of pneumatically drying the material, as well as product conveyance through the system. The entire system operates under negative pressure, which makes for a clean, dust-free operation.
On larger systems, an inlet damper is provided to allow for airflow control, on smaller systems a variable frequency drive may be used for the same purpose.
Select the AST feeder option
that’s right for you
The Feeding System controls the flow of product into the dryer, providing a constant and controlled feed to the dryer. Scott Equipment manufactures two feeders designed for hard-to-feed products that are difficult to pump or screw-feed consistently.
DISCOVER
Scott Cake Feeders
Scott Equipment Company has developed a versatile feeding system that a variety of process industries have come to rely on for their material handling requirements.
The Scott Cake Feeder is durably constructed with a cylindrical barrel and vertical agitator. The insightful design of the vertical shaft provides a consistent flow of material for the horizontal discharge screw.
The horizontal discharge screw may be fitted with a screw conveyor section or positive displacement pump for materials such as solid shortening, filter cake, and wet pet food.
Scott Equipment Cake Feeders Features
Bridgeless, trouble-free feeder for materials with consistency of a cake or paste
- Carbonates
- Oxides
- Clays
- Pigments
- Mica
May be fitted with a screw conveyor discharge section or a pump discharge section
(or a combination of the two when required for material cross-over and versatility)
Variable frequency drive for product feed
Can be supplied with a pump for thixotropic slurries/filter cakes
DISCOVER
Scott Mixer Feeders
The Scott Mixer Feeder was developed as a trouble-free feeder for materials with a non-flowing consistency and a steep angle of repose.
It was specifically designed to handle hard-to-feed products such as belt pressed sludges, wet granular materials, warm or sticky materials, and fibrous materials.
Its innovative design provides advantages over a live-bottom feeder with substantially fewer moving parts.
Scott Equipment Cake Feeders Features
Bridgeless, trouble-free feeder for materials with a non-flowing consistency and a steep angle of repose
- Belt/Filter pressed slurries
- Coal fines
- Fly Ash (Wet Sand)
- Virtually any material with an angle or respose > 60°
Superior to a live-bottom feeder due to lower maintenance required because of substantially fewer moving parts
(two bearings and two drives are all that are required)
Fitted with a screw conveyor discharge section
Avoid inferior drying solutions.
put our experience to work for you
CONTACT US TODAY TO LEARN ABOUT AST DRYER OPTIONS
Get in Touch
Built To Last
BUSINESS HOURS
Monday - Friday
8:00 am - 5:00 pm
US Central Time
OUR PRODUCTS
CONTACT US
605 4th Ave NW
New Prague, MN
56071
info@scottequipment.com
1-800-394-2591
(952) 758-2591
AFFILIATIONS
OUR PRODUCTS
BUSINESS HOURS
Monday - Friday
8:00 am - 5:00 pm
US Central Time
Monday - Friday
8:00 am - 5:00 pm
US Central Time
FIND US
605 4th Ave NW
New Prague, MN
56071
info@scottequipment.com
1-800-394-2591
(952) 758-2591
© Scott Equipment Company. All rights reserved. Privacy Policy
Website Design by Dohmain Designs
© Scott Equipment Company. All rights reserved.
Privacy Policy